Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
CertainTeed Flashing Replacement: The Whitney Owner’s Guide
We replace failed CertainTeed flashing on Whitney roofs, and most jobs land between $395 and $1,450 installed depending on where the flashing sits and how much of it has to come off. The overwhelming majority get scheduled within a few days of your call. That’s the short answer. The longer one starts with how you found this page.
Most Whitney homeowners don’t go looking for flashing. The flashing finds them. A brown water stain blooms on the ceiling a foot inside an exterior wall, or the paint on a fascia board starts peeling from the top down, or the sheet metal over the garage pops loose in a windstorm. Sometimes it’s simpler: a contractor doing an unrelated repair takes one look at the wall step and says, “You’ve got a gap there.” Either way, the flashing on a CertainTeed installation is what keeps water out of the seams your shingles don’t fully cover, and when it fails, you’ll hear about it inside the house before you see it on the roof.
Which CertainTeed Models This Applies To
Flashing isn’t a “CertainTeed” part the way a shingle is. CertainTeed makes roofing systems, and the flashing on your roof is matched to the shingle system, not stamped with a brand on every piece. On Whitney homes we most often see it working alongside Landmark, Landmark Pro, XT 25, and Presidential Shake lines, with the wall and step flashing cut to fit the specific install. So the label you’re looking for normally isn’t on the metal. It’s on a shingle wrapper in the attic, on the original bid paperwork, or on the label of the last bundle someone stacked in the garage.
Here’s the gotcha a lot of owners trip on: the flashing profile has to match your sidewall, your roof pitch, and the thickness of the shingle course it tucks under. CertainTeed’s heavier lines – Presidential and the laminated Landmark Pro in particular – sit taller than a three-tab, and we’ve pulled plenty of Whitney step flashing that was cut for a thinner shingle and never seated right to begin with. That’s a compatibility problem, not a wear problem, and it’s why the leak came back. On the OEM question: CertainTeed-proper accessories are the safest match when the detail calls for it, but for the L-metal and step pieces themselves, a quality 26-gauge formed aluminum or a proper copper equivalent does the job for decades. We’ll tell you which one your detail actually needs rather than selling a brand you don’t.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your CertainTeed Flashing Replacement Is Failing
Flashing hides at the seams, so the symptoms show up somewhere else. These are the five we see most on Whitney roofs:
- Staining on interior ceilings or walls near a chimney or sidewall. The water is getting behind the flashing and running down the sheathing until it finds a way through the drywall. By the time it shows, it has usually been traveling for a while.
- Peeling paint or rotting siding directly above the roof line. Water backing up under the flashing wicks into the fascia and the bottom courses of siding. If a fascia board is soft when you press it, the flashing above it isn’t shedding the way it should.
- Lifted, curled, or visibly bent metal. Thermal movement and the Nevada sun work on old flashing until it pulls its fasteners. Once it’s standing off the surface, wind-driven rain gets behind it.
- Loose or missing fasteners you can see from the ladder. Nail heads backing out of step flashing, or sealant smeared over a joint where a piece should have been replaced. Sealant is a patch, not a fix, and it fails first.
- Water in the attic after a storm, especially on the walls facing the weather. Soaked insulation or dark streaks on the sheathing near the chimney or wall line point straight at the flashing detail.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Whitney, most flashing replacement runs in these ranges. Every quote is written line-item, so you see parts and labor split out before we start.
| Scope | Typical installed range |
|---|---|
| Single chimney or wall flashing section | $395 – $650 |
| Multiple step-flashing runs, one wall | $650 – $950 |
| Chimney plus sidewall, full detail | $950 – $1,450 |
| Add a deck inspection while we’re up there | No charge |
What drives the number: how many linear feet, whether we’re working against a chimney or a simple wall step, how much surrounding shingle has to be carefully lifted and reset, and whether there’s rot underneath once we open it up. We don’t quote one price on the phone and a different one at the door. If we find soft sheathing once we’re in, we stop and show you before we touch anything else. Every flashing job is covered by our written 90-Day Done Right Promise – if it’s not done right, we make it right, and one call brings Bill back.
DIY or Call Us?
The honest split: you can safely get on a sturdy ladder and look. Check for lifted metal, missing nails, cracked sealant, and staining above the roof line. Take pictures. That tells you whether you have a flashing problem or something else. What you shouldn’t do is climb onto a pitched roof to re-seat step flashing yourself, and you should never work around a chimney or a wall step without fall protection and the right tools. Flashing replacement also means lifting and resetting shingles, and if you don’t get that back down correctly, you’ve traded a slow leak for a fast one. This is one of those jobs where the wrong first attempt costs more than the original repair. If the ladder is already making you nervous, that’s your answer.
The one place we’d rather you didn’t check yourself: anything that puts you on a roof with any pitch or height at all. A fall off a one-story roof ends up worse than any flashing repair. Call us instead.
If you’ve got a leak at a seam, call (844) 797-9455. A live person answers, day or night, and we’ll get eyes on it before you spend a dime.
FAQs
On a Whitney roof, formed aluminum flashing typically gives you 20 to 30 years before it’s earned a look; copper goes considerably longer. The metal often outlives the sealant and fasteners holding it, which is why an 18-to-20-year-old roof can leak at a seam even when the metal itself looks fine. Nevada’s sun and thermal swings are hard on the joints more than the panel. If your roof is original to a home built before roughly 2005, it’s worth having the flashing checked. Call (844) 797-9455 for a free estimate.
Sometimes, yes – a reseal or a re-fastened section is a legitimate fix when the metal is sound and it’s only the joint that let go. But once the flashing is bent, corroded, or was cut for the wrong shingle profile to begin with, patching it just buys you another leak next season. We’ll tell you honestly which one you’ve got. Call (844) 797-9455 – estimates are free.
A single section is usually a few hours; a chimney plus wall detail is most of a day. We’ll give you a realistic window when we quote it, not a best-case number. Call (844) 797-9455 to get on the schedule.
We match the flashing to your roof’s profile and pitch and bring the right gauge and material to the job – we don’t stock parts or carry them on a truck. We also work with GAF and Owens Corning systems when a Whitney roof was installed with one of those, so we’re not stuck on one brand. Call (844) 797-9455 for a free estimate and a straight answer on what your detail needs.
Shepherd & Sons Roofing Whitney installs products from GAF, CertainTeed, Owens Corning, IKO, Atlas, Tamko, and Boral, and we’re an independent service provider – not affiliated with CertainTeed. Same address since 1996, and the name on the truck is the name on the license. Call (844) 797-9455 for a free estimate, or a free second opinion on any written quote you’ve already got. No trip charge inside our own county, and $40 off any repair over $200.
Written by the team at Shepherd & Sons Roofing Whitney, serving Whitney and nearby areas.